Aastra Telecom Cell Phone 41 001348 00 Rev 04 User Manual

6725ip Phone Quick Reference Card  
Phone Requirements  
Parts List  
Microsoft Lync Server 2010  
LAN - 10/100/1000BaseT Ethernet, category 5/5E/6 straight through cabling  
Power source - IEEE 802.3af Power-over-Ethernet source or the Aastra 48V Power Adapter (Optional Accessory)  
®
6725ip Phone  
Documentation  
Phone  
Handset  
Ethernet  
Cable  
USB Cable  
Handset  
Cord  
Telephone Base  
Desk Legs  
Setting up your phone  
To connect the handset to the phone:  
Front Panel  
Softkeys  
1. Connect one end of the handset cord (B) to the handset (A)  
and the other end of the handset cord (B) to the handset jack  
on the back of the phone (C).  
A
B
C
2. Guide the cord through the channel on the back of the phone  
to the outer edge (as shown in the “Back Panelillustration).  
OK  
OK/Navigation Key  
Incoming Call Light  
Back Key  
To connect the legs to the phone:  
A total of four diꢀerent viewing angles allows you to  
personalize your viewing preference.  
Home Key  
Voicemail Indicator  
Keypad  
OK  
Uniꢀed Communications (UC)  
Presence Logo  
1. Attach each leg by inserting the tabs on the leg into the slots  
on the bottom of the phone. There are three pair of leg  
slots on each corner of the phone (D).  
D
Headset Key  
Speakerphone Key  
2. For a higher viewing angle, use the second and third slots from the top.  
3. For a lower viewing angle, use the ꢁrst and second slots from the top.  
4. Push the stand towards the phone until it snaps into place.  
Volume Down Key  
Volume Up Key  
Mute Key  
To connect to the network:  
USB Port USB Port Ethernet Ethernet  
Type A Type B LAN Port PC Port  
1. Connect one end of the RJ-45 Ethernet cable (supplied)  
into the port marked “LANon the base phone.  
2. Connect the other end of the Ethernet cable into your  
network source jack.  
Back Panel  
Leg Slot Locations  
For Ethernet networks that DO NOT supply  
Power-over-Ethernet to the phone:  
AN  
PC  
1. Connect an Aastra 48V power adapter (optional accessory)  
to the power port on the base phone and plug the other end  
into a wall power outlet.  
48V Power Port  
Headset Jack  
Handset Jack  
(connection not required if power  
provided over Ethernet connection)  
(Optional) Connect the phone via USB  
to your computer  
Handset Cord Channel  
To connect the phone to your computer:  
1. Connect the USB Type B connector on the USB cable (supplied)  
to the Type B port on the base phone (see illustrtation above).  
USB Type B  
connector  
to phone  
USB Type A  
connector to  
computer  
TM  
2. Connect the USB Type A connector on the USB cable to a USB port  
on your computer.  
 
41-001348-00 Rev 04  

Acoustic Research Home Security System ARRX18G User Manual
Addonics Technologies Computer Drive AESNAPMRI User Manual
ADTRAN Switch ADT 1234POE User Manual
Agilent Technologies Switch 34980A User Manual
AG Neovo Flat Panel Television H 17 User Manual
AllerAir Air Cleaner 4000 D AH User Manual
Aluratek Network Card AVH100F User Manual
Audiovox Automobile Alarm PRO 9775 User Manual
Axis Communications Security Camera P5532 User Manual
Axxess Interface Corded Headset OESWC LAN11 RF User Manual