American Standard Hot Tub 2645 Series User Manual

SCALA™ 5-1/2  
2645 SERIES  
WHIRLPOOL/BATHING POOL  
INSTALLATION INSTRUCTIONS  
HIGH GLOSS ACRYLIC  
SHOWN LESS ALL FITTINGS  
THANK YOU...  
for selecting an American Standard bath. Your new  
bath is shipped to you after careful inspection. The  
whirlpool version is completely assembled with pump,  
motor, and system piping. All you need to finish the  
installation are your selected fittings and electrical  
connections for a whirlpool.  
302mm  
(11-7/8)  
1676mm  
(66)  
RECOMMENDED FITTING LOCATION  
64 X 330mm (2-1/2" x 13")  
6mm  
(1/4)  
TYP.  
HAND SHOWER  
OUTLINE OF CUTOUT  
1626mm X 864mm  
(64 X 34)  
LOCATION  
51mm  
(2)  
25mm (1)  
TYP.  
To insure maximum performance and pleasure from  
this product, please follow the instructions and  
cautions.  
ON/OFF  
SWITCH  
914mm  
(36)  
List of Optional Components (not included):  
• Apron Kit*  
* see your American Standard Distributor  
PUMP  
229mm X 305mm  
(9 X 12) CUTOUT  
FOR DRAIN  
List of Required Components (not included):  
• Drain 1583.470*  
• Bath Filler*  
419mm  
(18)  
* see your American Standard Distributor  
44mm  
(1-3/4)  
List of Required Tools and Supplies:  
C/L OF  
DRAIN  
PROVIDE ACCESS  
TO PUMP FOR  
SERVICING ON ALL  
INSTALLATIONS  
Tools  
Supplies  
210mm  
(8-1/4)  
• Level  
• Nails  
LEVELING STRINGER  
• Tape Measure  
• Pipe Wrench  
• Slip Joint Pliers  
• Screw Driver  
• Standard  
• Putty  
(NOT FOR SUPPORT)  
• Caulking (waterproof)  
• 1 x 3 or 2 x 2  
Stringers  
38mm  
(1-1/2)  
102mm  
(4)  
• Drop Cloth  
• 15 amp  
GFCI Outlet  
• Cement, Plaster,  
Grout  
Woodworking Tools  
• Personal Safety  
Equipment  
464mm  
(18-1/4)  
502mm  
(19-3/4)  
• Caulking Gun  
44mm  
(1-3/4)  
GENERAL INSTALLATION INFORMATION  
Carefully uncrate and inspect your new bath for any  
shipping damage. If such damage is found, report it to  
your vendor immediately.  
INTEGRAL  
FEET SUPPORT  
457mm  
(3-5/8)  
1-1/2 N.P.T.M. THREADS  
1-1/2 O.D. TAILPIECE  
After inspection and during installation, protect the bath  
from construction damage. After installation, and before  
enclosing with wallboard, tile, etc., water test the unit  
and check for leaks.  
GENERAL SPECIFICATIONS FOR 2645 WHIRLPOOL  
If a whirlpool, do not make modifications to the whirlpool  
system or remove pump from factory mounting. This  
could adversely affect the safety and performance of the  
whirlpool and void the warranty. Do not handle or move  
the whirlpool by the pump, motor, or piping system.  
66 x 36 x 19-3/4 In. (1676 x 914 x 502mm)  
95 Lbs. (43 Kg.)  
INSTALLED SIZE  
WEIGHT  
595 Lbs. (268 Kg.)  
60 Gal. (227 L)  
55 Gal. (208 L)  
46 x 24 In. (1168 x 610mm)  
62 X 31-1/2 In. (1575 x 800mm)  
13-1/4 In. (337mm)  
WEIGHT w/WATER  
GAL. TO OVERFLOW  
WHIRLPOOL MIN. OPERATING VOL.  
BATHING WELL AT SUMP  
BATHING WELL AT RIM  
WATER DEPTH TO OVERFLOW  
FLOOR LOADING  
Fittings (bath filler, shower arm, etc.) are not provided  
with the bath and must be ordered separately. Framing  
and enclosing materials are provided by others. Check  
for availability of optional American Standard wall tiling  
bead (required for recess installations).  
36 Lbs./Sq.Ft. (175 Kgs/Sq.m)  
(PROJECTED AREA)  
PTS.  
CUBE (FT3)  
25.6  
45.1  
WHIRLPOOL ELECTRICAL SPECIFICATIONS  
SYSTEM I PUMP  
1.1 HP, 9.9 AMPS,120V.  
Protect all finished surfaces of the whirlpool during  
construction and installation using a drop cloth.  
WARNING! Do not lift whirlpool by the piping har-  
ness at any time.  
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.  
© American Standard Inc. 2003  
All product names listed herein are trademarks  
750733-100 Rev. F  
of American Standard
 
nc un
 
ess otherwise noted  
 
ELECTRICAL INSTALLATION INSTRUCTIONS  
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other  
applicable codes.  
WARNING:  
When using electrical products, basic precautions should always be observed, including the following:  
1. DANGER: RISK OF ELECTRIC SHOCK  
Connect only to a circuit protected by a ground-fault circuit interrupter.  
2. Grounding is required. The unit should be installed by a licensed electrician and grounded.  
3. Install to permit access for servicing.  
4. All building materials and wiring should be routed away from the pump body and heater (if equipped).  
The whirlpool should be installed on a 120 vac, 15 amp dedicated circuit. The circuit should be hard-wired from the  
electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel. A grounded  
neutral wire and a third wire, earth ground, are essential.  
ELECTRICAL INSTALLATION  
SEPERATE  
15 AMP  
GFCI OUTLET  
WHIRLPOOL MOUNTED  
120 VAC  
AIR SWITCH OR  
WALL TIMER  
PUMP/MOTOR  
GND.  
ELECTRICAL DIAGRAM  
READ AND FOLLOW ALL INSTRUCTIONS  
(3)  
750733-100 Rev. F  
 
WIRE SELECTION GUIDE  
Maximum distance from  
fusebox to motor  
The sizes shown on this  
chart are recommendations  
for copper conductors  
only. Always follow  
local and national  
50'  
100' 150'  
115V Power Line  
12 10  
200'  
Motor High  
Performance  
electrical codes  
12  
8
1.1  
DRAIN CONNECTION AND SYSTEM TEST  
Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the  
pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of  
the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings  
are factory tightened and inspected, some loosening may have occured during transit.) Make sure the whirlpool is  
connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the  
whirlpool is running.  
POST INSTALLATION CLEAN-UP  
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.  
Do not use wire brushes or any other metal implement on bath surface.  
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or  
®
stains may be removed using granular Spic and Span mixed with water.  
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.  
HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.  
Abrasive cleaners must not be used since they will scratch and dull the surface. Dulled areas can be restored by rubbing  
with a white automotive-type polishing compound and waxing with a liquid wax.  
®
(4)  
SPIC AND SPAN IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE  
750733-100 Rev. F  
 

3M Water System SF1XX User Manual
321 Studios Coffeemaker 4DX 33 User Manual
Accusplit Watch A725MXT User Manual
Adaptec Network Card PC 104 User Manual
Addonics Technologies Computer Hardware RT54S2HMEU User Manual
Agilent Technologies Power Supply 66lxxA User Manual
Alloy Computer Products Switch NS 16T01FS User Manual
American Standard Automobile Accessories APS 997 User Manual
American Standard Hot Tub 754323 100 Rev A User Manual
Axis Communications Inflatable Bouncy Toy T94B01M User Manual