Eureka Tents Tent Nergy 1210 User Manual

4. At A, insert the web corner pin into the end of the  
tent pole ferrule. At B, grasp the tent corner pin in one  
hand, the tent pole in the other. Arch the pole and  
place the pin into the end of the pole. See Fig 3 & 4.  
Repeat this with the second pole from C to D raising the  
tent as you go. See fig 5.  
7. Attach the fly to the poles. Lay out the fly with the inside side up, on ground at the front of  
the tent. Fit the fly poles into the pockets sewn to the hem. The poles run from side to side  
down the center of the fly forming an X. Secure the fly to the poles by wrapping the hook &  
loop fastener around the fly poles. See fig 9, 10 and 11.  
Assembly Instructions  
for the N!ergy 1210 Tent  
fig 9  
Component List:  
fig 3  
fig 4  
1 Tent  
2 Tent Poles  
1 Carry Bag  
1 Rain Fly  
6 Pull Out Cords  
B
1 Stake Bag W/Stakes  
2 Fly Poles  
1 Gear Loft  
1 Pole Bag  
1 Divider  
NOTE:  
fig 11  
Although it is possible to pitch this tent alone, it is faster/easier with two  
people.  
fig 10  
• Do not drop tent bag or pole bag on its end. Do not bounce tent bag on  
its end to get the tent out. These actions may cut the shockcord and/or  
damage the pole ends.  
The N!ergy series tents are pre-wired with three 12V outlets. Take care  
to keep them in their sleeves and avoid stepping on the sockets and  
wires during assembly.  
8. Attach the fly to the tent. Turn the fly assembly over and align it so  
that the poles point out over the doors. Grasp the corners of the of the  
fly and drag them up and over the roof to completely cover the tent.  
(This is much easier with two people)  
At the corners of the tent, reach under the fly and attach the hook & loop  
straps to the tent poles, securing the fly in place. See fig 12.  
A
fig 12  
At the bottom/corners of the tent, attach the shockcorded J-hooks to the  
rings on the corner webs. See fig 13.  
fig 13  
1. Unroll and unfold the tent on the ground. Separate the rest of the  
components and place to one side. Open the door before pitching the  
tent. Do not stake the tent down (however, in windy conditions, stake  
down one corner that faces into the wind).  
fig 5  
9. Tie a guy rope to each of the 4  
rings attached to the fly and stake  
out. Adjust tension with the in-line  
sliders. See fig 14 & 15.  
D
B
fig 14  
5. Start at the bottom and attach all the clips to  
the poles to create a freestanding tent. Place it in  
the desired location. See fig 6.  
A
C
fig 1  
2. Assemble all of the shockcorded poles. Keep the end sections from  
snapping together, as this can damage the ends. Make certain each  
plain end has been properly seated into the metal ferrule.  
fig 15  
fig 6  
fig 7  
6. Stake the tent down through the  
corner loops. Stake the opposite corners  
while applying tension to smooth the  
floor wrinkles. Also, stake out the beckett  
beneath each of the side windows. See  
fig 7 & 8.  
YOUR TENT IS READY !  
tent poles  
fly poles  
E! Power System: To use, you will need a power source. Our E! Power Pak™ is sold separately. Once connected to  
power, the control will display “green” at any switch that is “ON” and the “ON” socket will glow blue. See fig 16.  
E! Power Port: Open zipper and run extension cord through opening.  
Close zipper so that it rests next to the extension cord. Make sure the  
zipper cover is not twisted or tucked. The cover must lay flat against  
the outside of the tent to keep out rain.  
blue  
3. Insert an assembled pole  
through both sleeves from A to  
B. Insert the second pole through  
the sleeves from C to D, forming  
an X across the tent. See fig 1.  
There is a fabric loop at the tent’s  
peak. Capture this loop with the  
top pole as you move through  
the sleeves. See fig 1 & 2.  
Accessories: E! Power Fan/Light, E! Power Reading Light and an E!  
Power 12v Adapter Cord.  
green  
Sweep Out: Inside, at the bottom of the door is a sewn-in web loop. Pull  
this loop to the outside and stake it down to provide a ready exit for  
floor sweepings. See fig 17.  
fig 16  
fig 17  
Take Down: Pull up all stakes. Release the fly’s hook & loop straps. Remove fly.  
Remove fly poles. Remove clips from tent poles and pull poles off of the pins.  
Collapse all poles and stow. Fold the tent onto itself then fold the fly and lay it  
on tent. Roll up both towards the open door and stow.  
fig 8  
REV D 4.09  
fig 2  
Read the important safety instructions on the reverse side.  
 
SEAM SEALING:  
CLEANING:  
• Clean the tent by setting it up and wiping it down with a mild soap (liquid hand  
soap) and lukewarm water solution. Rinse thoroughly and dry completely.  
Never use detergent, washing machines or dryers because they can damage  
the tent’s protective coating and seams. After cleaning, be sure the tent is  
completely dry, especially the heavier, double-stitched areas such as the  
seams, before storing or mold / mildew are likely to grow.  
Clean the tent poles with a cloth and lubricate them with silicone spray. This is  
especially necessary after ocean side camping to remove salt spray so the  
poles don’t corrode or stay gritty.  
Clean the zippers with a quick dip in water and then dry them off. This is  
especially important if you’ve been camping in a location with sand/dirt. If you  
don’t clean the zippers, the sliders will wear out and eventually the teeth will  
become inoperable.  
We recommend use of a sealer such as Kenyon Seam Sealer 3 or  
McNett Outdoor SeamGrip®.  
Work in a fully ventilated area.  
• Set the tent up or lay the tent out flat. Taut seams allow for even  
application and penetration of the sealer.  
Decide which seams need to be sealed. Seams that will be exposed  
to rain, runoff, or ground level water are a must for sealing, seams on  
uncoated nylon or mesh panels don’t need treatment. There is no  
need to seal the seams in the roof or the factory taped seams. We  
recommend sealing both floor and fly seams and reinforcements.  
Apply sealant to the inside and outside of all exposed seams. Several  
thin layers will work better than one thick layer. Read and follow  
manufacture’s instructions.  
electrocution or electric shock hazard  
The use of the Power Port with an extension cord running  
in to the tent could result in electrocution or electric shock,  
or fire or explosion hazards. For these reasons, when using  
the Power Port:  
fig.b  
fig.a  
fig.c  
DO NOT allow an extension cord or any electrical device to come into  
contact with water or condensation inside the tent.  
DO NOT use an extension cord if it is worn or damaged.  
CONDENSATION & VENTING:  
Through perspiration and breathing, an adult gives off about a pint of water  
overnight. If it cannot escape, the water vapor condenses to liquid. Most often,  
water found in the tent is a result of this condensation rather than from the tent  
leaking. Condensation often forms where the sleeping bag touches the side of  
the tent, under the sleeping pad, or on coated surfaces such as the door aps. A  
tent’s double wall construction allows the vapor to escape through the roof to the  
outside, keeping the inside of the tent dry.  
Leave windows partially open at night to provide cross ventilation and further  
reduce condensation. Cross ventilation becomes more important in very humid  
or extremely cold conditions when the permeable roof is less effective. The  
DO use only extension cords that are marked for OUTDOOR USE.  
DO connect extension cord only to a 120Volt GFCI protected outlet with  
proper ground. If GFCI outlet is not available, use an extension cord with  
GFCI protection built in.  
DO make sure the part of the extension cord that is outside the tent is lower  
than the power port so that rain will not follow the cord into the tent.  
DO follow all warnings, instructions, and safety precautions from the  
manufacturer of the extension cord.  
To reduce risk of damage to electric plug or cord, pull by the plug rather than  
the cord when disconnecting the E! Power Pak from an extension cord.  
Your failure to follow these warnings could cause death, serious injury or  
permanent disability to you or others. It is always recommended to have  
someone nearby to assist in case of an emergency.  
ALTERATIONS OR MODIFICATIONS:  
STAKING:  
DO NOT misuse, modify or alter this product in any way from its condition at the  
time of sale. Alteration, modification or any use of this product contrary to the  
accompanying written instructions shall void the warranty. Moreover, any  
misuse, alteration or modification of the product shall absolve Johnson  
Outdoors Gear LLC of any liability for property damages or injuries sustained  
as a result of such misuse, modification or alteration.  
All tents need to be staked down to keep them from blowing away.  
Placing heavy objects inside is just not adequate.  
• Once the tent body is erected, stake it out before the fly is put on. This  
enables you to square the tent up to ensure that the fly goes on  
properly and that the seams align with the frame. Pull the base of the  
tent taut between each web stake out loop or ring & pin. Make sure  
that all corners are square. It is important that you don’t stake the  
tent out too tightly. You will know it’s too tight, if the door zippers can  
not be easily operated. Drive stakes through the web loops, or with  
ring & pin, drive the stake just outside the ring so that the “J” hook  
catches it. Tie a piece of cord or web into a loop through the ring to  
be used as a large stake loop if needed.  
With the tent properly staked, drape the fly over the frame, attach its  
tent connection points and stake down any pull outs.  
Do not attempt to remove the stakes by pulling on the tent becket  
loop, as this could cause the fabric to tear. The best way is to pry on  
the stake itself.  
features that enhance ventilation are windows, short-sheeted flys (bottom  
venting), roof vents, and High/Low venting doors. These are specific to each tent.  
-
LIMITED WARRANTY:  
What Is Covered: Johnson Outdoors Gear LLC warrants to the original purchaser  
that its products are free from defects in material and workmanship, for the life of  
the product, except as qualified below. The life of the product is determined from  
the date of purchase until such time as the product is no longer serviceable due to  
normal wear and tear.  
What Is Not Covered: Johnson Outdoors Gear LLC shall not be responsible for the  
natural breakdown of materials that occurs inevitably with extended use (e.g., Ultra  
Violet (UV) light damage on tents, exhausted zippers), or defects caused by accident,  
abuse, alteration, animal attack, storm damage, misuse or improper care.  
THERE ARE NO OTHER EXPRESS WARRANTIES BEYOND THE TERMS OF THIS LIMITED  
WARRANTY. IN NO EVENT SHALL JOHNSON OUTDOORS GEAR LLC BE LIABLE FOR  
INCIDENTAL OR CONSEQUENTIAL DAMAGES.  
Some states do not allow the exclusion or limitation of incidental or consequential  
damages, so the above limitation or exclusion may not apply to you.  
What Johnson Outdoors Gear LLC Will Do: If after inspection we find that a  
product failed due to a manufacturing or material defect, we will repair or replace  
the product, at our option, without charge.  
How to Obtain Warranty Service: Return the product, freight prepaid, to the Dealer  
from whom it was purchased; or, contact our Customer Satisfaction Department for  
return authorization: toll free 1-800-572-8822. Collect shipments or shipments  
without return authorization cannot be accepted. The product registration card  
packaged with our product need not be returned for the warranty to be effective  
and for you to receive warranty service.  
Repairs: If your Johnson Outdoors Gear LLC product needs service or repair due to  
normal wear and tear, animal attack, accident or some other reason that is not  
covered under the warranty we will provide the necessary service for a reasonable  
charge, plus shipping and handling. We require that products accepted for any  
repair be properly cleaned according to our recommended care instructions. Please  
send your product or component that requires repair (e.g., tent fly), postage  
prepaid, along with a description of what needs attention. For service and repairs,  
please contact our Customer Satisfaction Department: toll free 1-800-572-8822  
How State Law Relates To This Warranty: This warranty gives you specific legal  
rights, and you may have other rights that vary from state to state.  
ULTRAVIOLET LIGHT:  
SAFETY INFORMATION: IMPORTANT SAFETY INSTRUCTIONS  
Save these instructions. This manual contains important safety and  
operating instructions applicable to the safe and efficient use of the E!  
Power Pak DC power source and your Eureka! E! Power shelter with 12v  
outlets.Failure to use the power pack in any way other than originally  
intended by Johnson Outdoors Gear LLC will void the warranty and may  
damage the unit or result in injury.Use of an attachment not recommended  
or sold by Johnson Outdoors Gear LLC may result in risk of fire, electric  
shock, injury to persons, or property damage.The E! Power Pak is not  
intended for use by children at any time.  
DO NOT insert any foreign objects into the 12v outlet on the E! Power Pak, or  
the 12v outlets in the shelter.  
DO NOT expose the E! Power Pak or 12v outlets in the shelter to water, rain,  
snow or spray.  
Ultraviolet light damage to tent fabric is caused by excessive exposure to sunlight.  
While our fabrics are UV resistant, any synthetic fabric is susceptible to UV  
degradation. UV damage will cause nylon and polyester to become brittle and  
tear easily. We recommend that you use the rain fly even on clear days. It acts as  
a sunscreen to the tent. A rain fly is both easier and less expensive to replace if  
damaged. UV damage can be minimized by erecting tents on shaded sites with  
low exposure to direct sunlight.  
GENERAL POLE CARE:  
• Never let tent poles snap together as this can damage the pole end.  
Do not drop tent or pole bags on their ends and do not bounce a tent bag on its  
end to get the tent out. These actions may cut the shock cord and damage the  
pole ends.  
The aluminum frame may bend slightly and take a “set” through usage; this  
normally does not affect the performance of the frame.  
Staking in special conditions:  
• Sand. Use long, broad stakes with plenty of surface area.  
Hard, Rocky, or Frozen Soil. Steel stakes work best. Store steel  
stakes separately. Their sharp edges can cut fabric and leave rust  
stains, which might damage your tent.  
Snow. Use “dead man” anchors. Tie the tent to buried objects  
(branches, tent bags, or stuff sacks filled with snow); or tie tents to  
snow shoes, skis, or ski poles, which are stuck in the snow.  
GUY LINES:  
Do not depend on staking alone to keep your tent secure in high wind.  
Done correctly, the addition of guy lines can save your tent in  
exceptional weather.  
Make sure that each hook and loop fastener on the underside of the  
fly is securely wrapped around the tent frame.  
Attach the guy rope, from the stake bag, to each guy out loop on fly.  
Stake all guy lines 6’ out from the edge of the tent. The optimal angle  
from the ground to the guy line is 45˚. See fig a. In high wind,  
additional guy lines should be used. On the N!ergy 9 and 1210 add a  
secondary guy line off of each guy out point. See fig b.  
On the N!ergy 1310, guy ropes are pre-attached & stored in pockets at  
each guy out location. In high wind, attach a secondary line at each  
guy out point on the fly and half way down the tan mid-poles. See fig c.  
The N!ergy Screenhouse has pre-attached reflective guy ropes at each  
DO NOT connect any device with a neutral conductor (via an AC inverter)  
to the E! Power Pak or the 12v outlets.  
DO NOT use the E! Power Pak if it is damaged. Use care not to drop the unit. A  
drop or fall can damage the unit even though no visible damage may be  
apparent.  
DO NOT expose the E! Power Pak to temperatures over 104˚F/40˚C. Always  
store the E! Power Pak in a dry environment. Ideal storage temperature is  
70˚F/21˚ C.  
DO NOT permit the battery in the E! Power Pak to freeze. Never attempt to  
recharge a frozen battery.  
DO NOT disassemble the E! Power Pak. Incorrect reassembly may result in  
a risk of electric shock or fire.If your E! Power Pak requires service, call  
Schumacher Electric at 1-800-621-5485.  
GENERAL TENT CARE:  
• Sweep the tent floor daily to prevent damage from stones.  
Try not to wear shoes inside your tent.  
• Use a ground cloth whenever possible.  
Do not keep food inside a tent. Hungry critters will chew through tent fabric in  
search of food.  
STORAGE:  
Make sure the tent is completely dry, then store loosely rolled, in a dry, cool  
place. To prevent dust from collecting on the tent, cover it with a cloth. This  
allows the nylon/polyester fabric to breathe.  
Ideally, the tent poles should be stored in their fully assembled state. This  
reduces the tension on the shock cord, prolonging its life.  
The tent bag should be used only as a carry sack and not for storage.  
COLOR TRANSFER:  
Do to the nature of tent fabrics, color can transfer from darker to lighter fabrics  
when the two fabrics are in contact over time when wet, damp or exposed to the  
combination of moisture and high heat. This does not effect the tent’s  
performance. To prevent / minimize color transfer, always make sure your tent is  
completely dry prior to packing and storage.  
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC.  
This tent meets the flammability requirements of CPAI-84. The  
fabric may burn if left in continuous contact with any flame  
source. The application of any foreign substance to the tent  
fabric may render the flame-resistant properties ineffective.  
DO NOT operate any device which burns fuel inside your tent.  
Combustion consumes oxygen and can produce dangerous  
levels of carbon monoxide, which could lead to serious injury or  
death.  
Johnson Outdoors Gear LLC  
Your failure to follow these warnings could cause death, serious  
injury or permanent disability to you or others.  
REV. C FEB.09  
corner.  
 

Acer Computer Monitor P205H User Manual
ADC TV Cables BNC 26N User Manual
Allied Telesis Network Card 7112 User Manual
Alto Shaam Oven 300 HW SERIES User Manual
American Standard Hot Tub 1599205 User Manual
AMX Stereo System TX CT5 User Manual
AMX Switch AVS SL PR 0401 0601 User Manual
Atmel Computer Hardware 8 16 bit High Performance Low Power Flash Microcontrollers User Manual
Axis Communications Security Camera M1034 W User Manual
Badger Basket Stroller 09941 User Manual